CV 90 Photoetch Shootout

_DSC1235

This is a small in-box comparison review of the Voyager Model and KA Models photoetch kits for the Academy Stridsfordon 9040B kit in 1/35.

Let´s start with the Voyager Model set.

VoyagerModel Modern Swedish Infantry Vehicle PE 35383

The set comes in a small but quite sturdy cardboard box. Inside there are two sheets of instructions (three sides in all) and a plastic bag containing a medium sized PE fret and two small, jam packed with details. There is also a small plastic bag containing two pieces of plastic rod of different diameters. The bag containing the parts are taped to a sheet of cardboard and the frets should be safe for transport, but..

Someone who packed my kit was a bit careless when jamming the frets into the bag, and the result is that a few pieces have been bent, and a pair of them have been damaged, requiring some finesse and tlc when used.

The set contains among other things, meshes for the air intakes on top of the engine and radiators and a mesh for the hot air exhaust to the rear.

Also included are the side skirts and details for them, the thread plates around the crew hatches and also parts for enhancing the interior on the gunners hatch.

Someone handier than me could probably make the side skirts and the rear hatch moveable.

A photoetched sight cover is also included, complete with the tiny hole that enables the use of the sight even when the cover is down.

The set was bought from Lucky Model and cost me $13.29.

KA Models CV9040B Detail-Up set MM-35006

This set comes in a resealable plastic bag similar to the one Eduard sets comes in, but slightly larger. Inside there is a piece of cardboard on which another plastic bag containing the single large fret is taped. Also in the bag is a short length of brass rod. On the opposite side of the fret there is a single folded sheet of paper that contains the instructions.

The large fret has an area that is probably a bit larger than the combined area of the Voyager frets, however it is not packed as dense, thus the number of details you get are fewer.

Some of the details included are unsurprisingly the same as on the Voyager set. The thread plates, and meshes for the various intakes and exhausts. But KA Models has taken a slightly different approach and has included parts allowing you to make the radiator intakes completely out of brass, with the PE mesh covering a PE grille, all inside a PE frame. The exhaust “box” to the rear receives the same treatment. The whole structure can be built as a PE part with a three dimensional grille built from separate parts inside a PE frame. If done properly, this would probably look fantastic, but I don´t think this is for the faint of heart.

Also included in this kit are the two anchors that can be seen strapped to the upper left side of the vehicle. Those are not included in the Voyager set. On the other hand does this set not contain the photo etched side skirts and the myriad of small details that comes with the voyager set.

The set was also bought from Lucky Model and cost me $16.99

A bunch of pictures

The black and white instructions are from the voyager kit, the colour ones, from the KA Models  kit.

Which one would I choose?

If I was to choose between the two kits I’d go for the Voyager kit, but the two sets do complement each other in some respects. But I am not entirely convinced that the anchors and the very complicated radiator intakes/exhausts are worth the trouble. The Voyager set is cheaper, contains more detail and seems to be easier to use. The only downside to the Voyager set is that my sample was slightly damaged.

Thanks for reading this far. :-)

About Erik Gustavsson

One of the founding fathers of Plastic Warfare, and the creator and administrator of this website.
This entry was posted in Reviews, Swedish Plastic. Bookmark the permalink.

2 Responses to CV 90 Photoetch Shootout

  1. Jim says:

    Thank you Erik, I have had a hard time deciding which detail sets to get–My time is limited right now so scratching anything is out of the question. I only wish that someone would make a recovery conversion kit for the Strf9040 AND someone should make Swedish troops to go with these vehicles–jungle, desert and winter Battledress uniform. Sorry to ramble but I want more Swedish Armor and Troopers.
    Regards,
    Jim

    • Erik Gustavsson says:

      As the academy kit comes, a vanilla Strf 9040B, the resin figures from D-Toys should work just fine. But I definitively agree that there should be more Swedish figures available, preferably some in the newer light weight garments that has been used in Liberia and Afghanistan, to go with the forthcoming Strf 9040C. But some regular guys from the 80’s and 90’s to go with the HobbyFan kits of the Pbv 302, Ikv 91 and Strv 104 would be welcome too.

      I hope the article helped you in your decision process. :-)

      /E

Leave a Reply to Erik Gustavsson Cancel reply

Your email address will not be published. Required fields are marked *